Type 2 hardware provides new cables and connectors between the I/O cards and main boards in Cores and I/O Frames. Due to this change, the Type 2 hardware is not physically compatible with the older hardware. You can still integrate the new I/O Frames and Cores in the same system with older hardware, but the I/O cards are not interchangeable. Type 2 hardware can be identified by a yellow label on the back of the Core and I/O Frame, and the bottom of the I/O cards.
If a Mic/Line In card is used in a redundant I/O Frame or Core, wire the inputs in parallel with the corresponding card in the redundant I/O Frame or Core. For more details on redundancy and Mic/Line In cards, refer to the Redundancy topic.
For configuration information for the Line In Component, refer to the Mic/Line In topic.
This topic covers the hardware aspect of the Mic/Line In card.
Model CIML4-HP provides four channels of microphone / line-level analog audio input with 48V phantom power, and high performance pre-amplifiers and A/D converters.
|
High-Performance Mic/Line In CIML4-HP |
||
|---|---|---|
Dynamic range |
un-weighted |
> 112 dB |
|
A-weighted |
> 115 dB |
|
|
|
||
Distortion (20Hz - 20 kHz) |
+4 dBu (max) |
< 0.004% THD+N |
|
2 dB below clip (max) |
< 0.06% THD+N |
|
|
|
||
Crosstalk (20 Hz - 20 kHz) |
Inter-channel (max) |
> 110 dB |
|
Inter-channel (typ) |
> 110 dB |
|
|
Intra-channel (max) |
> 110 dB |
|
|
Intra-channel (typ) |
> 110 dB |
|
|
|
||
Frequency Response |
20Hz - 20 kHz (max) |
± 0.5 dB |
|
20Hz - 20kHz (typ) |
± 0.2 dB |
|
|
|
||
Input Impedance |
Balanced (nominal) |
10 k ohms |
|
Unbalanced (nominal) |
10 k ohms |
|
|
|
||
Common Mode Rejection |
20Hz - 20kHz (Min) |
> 45 dB |
|
20Hz - 20kHz (Typ) |
> 50 dB |
|
|
|
||
Input Sensitivities(continuously variable) |
Vrms |
1.23 to 17.35 |
|
dBu |
-56 to 27 |
|
|
dBv |
-58.2 to 24.8 |
|
|
|
||
Mute |
Digital Mute |
Infinite Attenuation |
|
|
||
Audio Converters |
Analog to Digital Conversion (ADCs) |
24-bit delta-sigma at 48 or 96 kHz sample rate |
|
Digital to Analog Conversion (DACs) |
— |
|
|
Group Delay |
0.25 ms |
|
|
|
||
Connectors |
— |
Four 3-terminal Euro-style detachable terminal blocks |
|
|
||
User-configurable Options(software enabled) |
Phantom Power |
+48 V phantom power (meets IEC 1938 [1996] spec) |
|
Input Sensitivity |
1.23 mV to 17.35 Vrms, -56 to +27 dBu |
|
|
Output Trim Vrms (max) dBu (max) dBv (max) |
— — — |
|
|
Amplifier Standby |
— |
|
|
Mute |
— |
|
|
Enable Meters |
— |
|
|
Audio Output Levels |
— |
|
|
|
||
Amplifier Model Support |
— |
— |
Model CIML4 provides four channels of microphone / line-level analog audio input with 48V phantom power.
|
Mic/Line In CIML4 |
||
|---|---|---|
Dynamic range |
un-weighted |
> 105 dB |
|
A-weighted |
> 108 dB |
|
|
|
||
Distortion (20Hz - 20 kHz) |
+4 dBu (max) |
< 0.009% THD+N |
|
2 dB below clip (max) |
< 0.08% THD+N |
|
|
|
||
Crosstalk (20 Hz - 20 kHz) |
Inter-channel (max) |
100 dB |
|
Inter-channel (typ) |
110 dB |
|
|
Intra-channel (max) |
100 dB |
|
|
Intra-channel (typ) |
110 dB |
|
|
|
||
Frequency Response |
20Hz - 20 kHz (max) |
± 0.5 dB |
|
20Hz - 20kHz (typ) |
± 0.2 dB |
|
|
|
||
|
Balanced (nominal) |
10 k ohms |
|
|
Unbalanced (nominal) |
10 k ohms |
|
|
|
||
Common Mode Rejection |
20Hz - 20kHz (Min) |
> 45 dB |
|
20Hz - 20kHz (Typ) |
> 50 dB |
|
|
|
||
Input Sensitivities(4 selections) |
Vrms |
0.123, 2.25, 8.70, 17.35 |
|
dBu |
-16, 10, 21, 27 |
|
|
dBv |
-18.2, 7.04, 18.8, 24.78 |
|
|
|
||
Mute |
Digital Mute |
Infinite Attenuation |
|
|
||
Audio ConvertersGroup Delay (measured at 48 kHz) |
Analog to Digital Conversion (ADCs) |
24-bit delta-sigma at 48 or 96 kHz sample rate |
|
Digital to Analog Conversion (DACs) |
— |
|
|
Input |
0.25 ms |
|
|
|
||
Connectors |
— |
Four 3-terminal Euro-style detachable terminal blocks |
|
|
||
User-configurable Options(software enabled) |
Phantom Power |
+48 V phantom power (meets IEC 1938 [1996] spec) |
|
Input Sensitivity |
1.23 mV to 17.35 Vrms, -56 to +27 dBu |
|
|
Output Trim Vrms (max) dBu (max) dBv (max) |
— — — |
|
|
Amplifier Standby |
— |
|
|
Mute |
— |
|
|
Enable Meters |
— |
|
|
Audio Output Levels |
— |
|
|
|
||
Amplifier Model Support |
— |
— |
© 2009 - 2016 QSC, LLC. All rights reserved. QSC and the QSC logo are trademarks of QSC, LLC in the U.S. Patent and Trademark office and other countries. All other trademarks are the property of their respective owners.
http://patents.qsc.com.
Related Topics